Now that's progress!

We are starting to get cool (high 70's, low 80's) temperatures and that sure helps when you are working hard outdoors.

As you can see below we finished the trim boards in the living room.   We are determined and anxious to take down the scaffolding in our living room Then we will have a room we can kinda use during the winter. We made the trim boards out of some of the pine #2 tongue and groove. Each board was stained with Early American stain.  The trim boards were cut 3" wide. The wall boards will remain natural.

. 

One of our greatest enjoyments is relaxing by a fire. We installed the double wall stove pipe to finish the installation of the cast iron stove. We used two 4' telescoping pipe with attachments at the top and bottom.  The brick below the cast iron stove was painted with a high heat black paint.  We purchased the stove pipe for this part of the installation from Promax Supply on eBay. If you are not in a hurry and you have patience and can persevere through their erratic ordering system, their price was almost 1/2 of the retailer we purchased other parts from. Here is a photo of our first fire!  We were following the instructions to burn several small fires to break in the stove. It was only about 65 degrees in the morning, so we went for it! Really nice!! The colorful magnetic thermometer came in very handing in keeping the temperature below 300 degrees for the first fires.

We are now entering hunting season as you can see below. So progress won't be as fast as it has been. 

Happy FALL YA'LL

Life Happens and the ceiling is tops!

8-13-17 Life happens...
The tongue and groove walls and ceilings are slow going, but getting done. Life happened and we had to delay some building. We are back on track and working through the 100 degree heat to install the tongue and groove walls and ceilings.  The living area walls are complete with the installation of the 1 x 8 x16 pine T&G.  The North side of the ceiling from the wall to the center beam was finished today.

Left to do: trim.  We have had a long standing discussion on the color of the trim. Matching or working out the colors of all the permanent fixtures, floor, walls, trim, etc. is difficult.  Hours of discussion go into deciding on staining, painting, tile or wood floors. Today we decided (again) to go with paint on the floors. We will let you see how that goes when we get to that juncture.

A bridge and our beam

In light of the amount of rain we have been getting we had to take a side step and build a bridge. This bridge will do the trick to get us back and forth from the shop to the house without sloshing through the mud. While the new gutters are helping tremendously, the sand is a soggy mess when wet. A simple DIY bridge and it works great!

Sam " hmmm what is that!?"

Finished are all the 10' walls in the living area!! 🏆🏆🏆

After finishing the wall with the main door and windows, we finished the beam.  We lightly sanded then textured the wood with a few handy tools.  Those marks make a wonderful look on the finished stained wood.  The scaffolding is a fantastic tool and made this staining job alot easier!

Wall continuation.. We have a DIY Mantel!

We are finding that the tongue and groove wall installation is going fairly quickly. Over 2-3 work days and about 12 hrs we have installed the pine boards up to 10' in our living area. Three walls!
Working around the electrical sockets and window frames are fairly simple.  The pins are working absolutely wonderful and the bowrench is worth its weight in gold! The kitchen wall where the cabinets will be installed has been left open. We will be installing plywood before the cabinets.

After searching and searching for a mantel we really liked and was in our price range, we opted to do a DIY mantel. We love it and think it turned out great! What do you think?  We used four 2" x 10" pine boards, glued and doweled together with 3/4" dowel.  Then the mantel was trimmed to a length of 5', sanded, textured and stained. The mantel was installed with the top at approximately 5'. The mantel was attached to the wall with 5/16 x 3 1/2" screws. Four screws were inserted from the back side of the wall. This mantel is sturdy and isn't going anywhere!

We picked up a 2" thick 36" cement square. This will be used under the cast iron wood burning stove that will sit in front of the mantel. I will be finding a way to stain that square.

We also installed wood trim around one window after testing a handful of stains. We were looking for something just slightly darker than the wall boards. We settled on Classic Oak. This is a stain and poly product that will only take one coat.  I like the slight overhang of the upper window trim. Nice touch!

WALLS !!!

Walls!  It makes me feel like we are getting closer to being done, although we are far from it.
We worked through all the hassle of getting the tongue and groove boards to the house. Now I am in training on installing boards as high up as I can reach (that is not far).  This way I can help while the Foreman works on other things. Here is my first wall. Short and sweet.

  

As luck would have it, the nail gun bit the dust and we both had to stop working. The process is relatively easy. My main goal was to get them on straight, level, tight, with the groove side out and nail in the top, not the notch, so the nail won't show. No problem....you can only see a couple nails.

Gutters and Buying wall boards

We are fortunate for the pretty good grading around the house and shop. We don't have too much to change, but between the two buildings the watershed is quite great in a heavy rain. We decided to add gutters to the side of the house shop to divert the water to the back of both buildings.  We contacted our local "Gutter man" / Fire Chief with Gutters Plus. They came and did an excellent job.  The continued rains have proven the gutters were well worth it!

After much debate and searching for wood sources in our area we ordered and received 500 16' yellow pine tongue and groove boards. These are 1" x 8"  #122 boards. Originally we wanted white pine, but there was a lot of mix  up with the pricing and availability. That happens when sources are few.
These boards are going on all walls and ceilings. That is the reason we shopped around for 10' - 12' boards, but it may end up being a faster install with the 16' boards.  We should end up with a little left over, even with drops.
Temporary storage is not ideal with all the rain we have been having, but maybe it will get us moving faster on the installation!

Of course, as soon as the wood was delivered we had to try it out. So we started covering our living area beam.  It is looking good. we will be giving that beam texture and a dark coat of stain to make it really stand out.

Working on test pieces for stain.  The beam will be the darker stain on the far left. One of the three on the right will be the trim for all corners, windows and doors.

Insulation and Exterior Complete!

We hit a slow patch in our diy build.  But the insulation and building exterior are complete!!

The interior foam insulation was blown in using closed cell around the windows and open cell on the remaining walls and ceiling. The insulation makes a great difference in temperature inside.

The exterior has been completed by Huff Welding. They installed the last  pieces on the porch.

We moved over the swing to the front porch and moved over the fire pit and made a sitting area.

Now the interior building for us begins! We will be installing plywood in the closests and painting them at a later date. A few concrete anchors have been installed and two doorway thresholds removed.

We are in the process of finding the tongue and groove boards for all the walls. Not an easy task when you need 6000sq ft of boards (approx 900 10' boards). Hopefully, we will have that figured out in the next week and the boards on order. Until then we have alot of wall anchors to install and many other little items. 

BTW: We squeezed in a "little" garden to take care of in our "spare" time. Oh, and we have fun doing some wild blackberry pickin'.